三层架构综合实验（2.7）

目标：

一、首先需要对172.16.0.0 26这个地址基于该图进行合理的划分；

172.16.0.0 16

172.16.1.0 25（vlan1）

172.16.2.128 25（vlan2）

172.16.3.0 24（r1-r2）

LSW1：

SVI1:172.16.1.10 25 vlan1
SVI2:172.16.1.210 25 vlan2

LSW2：

SVI1:172.16.1.20 25 vlan1
SVI2:172.16.1.220 25 vlan2

二、现在进行交换机部分的配置

配置顺序：CHNNEL VLAN TRUNK STP SVI VRRP DHCP

（1）首先在sw1与sw2之间进行chnnel的创建逻辑的将两条线捆绑为一条线

[sw1]int Eth-Trunk 0
[sw1]int gi 0/0/4
[sw1-GigabitEthernet0/0/4]eth-trunk 0
[sw1-GigabitEthernet0/0/3]eth-trunk 0

[sw2]int Eth-Trunk 0
[sw2-Eth-Trunk0]int gi 0/0/4
[sw2-GigabitEthernet0/0/4]eth-trunk 0
[sw2-GigabitEthernet0/0/3]eth-trunk 0

（2）在sw3和sw4上创建vlan2并且将其划分到对应的接口，并且创建trunk干道

[sw1]vlan 2
[sw1]port-group group-member GigabitEthernet 0/0/2 gi 0/0/5 Eth-Trunk 0
[sw1-GigabitEthernet0/0/2]port link-type trunk
[sw1-GigabitEthernet0/0/5]port link-type trunk
[sw1-Eth-Trunk0]port link-type trunk
[sw1-port-group]port trunk allow-pass vlan 2
[sw1-GigabitEthernet0/0/2]port trunk allow-pass vlan 2
[sw1-GigabitEthernet0/0/5]port trunk allow-pass vlan 2
[sw1-Eth-Trunk0]port trunk allow-pass vlan 2

[sw2]vlan 2
[sw2]port-group group-member gi 0/0/2 gi 0/0/5 Eth-Trunk 0
[sw2-GigabitEthernet0/0/2]port link-type trunk
[sw2-GigabitEthernet0/0/5]port link-type trunk
[sw2-Eth-Trunk0]port link-type trunk
[sw2-port-group]port trunk allow-pass vlan 2
[sw2-GigabitEthernet0/0/2]port trunk allow-pass vlan 2
[sw2-GigabitEthernet0/0/5]port trunk allow-pass vlan 2
[sw2-Eth-Trunk0]port trunk allow-pass vlan 2

[sw3]vlan 2
[sw3]int e 0/0/3
[sw3-Ethernet0/0/3]port link-type access
[sw3-Ethernet0/0/3]port default vlan 2
[sw3]port-group group-member e 0/0/2 e 0/0/5
[sw3-port-group]port link-type tr
[sw3-port-group]port link-type trunk
[sw3-Ethernet0/0/2]port link-type trunk
[sw3-Ethernet0/0/5]port link-type trunk
[sw3-port-group]port trunk allow-pass vlan 2
[sw3-Ethernet0/0/2]port trunk allow-pass vlan 2
[sw3-Ethernet0/0/5]port trunk allow-pass vlan 2

[sw4]vlan 2
[sw4]int e 0/0/3
[sw4-Ethernet0/0/3]port link-type access
[sw4-Ethernet0/0/3]port default vlan 2
[sw4]port-group group-member e 0/0/5 e 0/0/2
[sw4-port-group]port link-type trunk
[sw4-Ethernet0/0/5]port link-type trunk
[sw4-Ethernet0/0/2]port link-type trunk
[sw4-port-group]port trunk allow-pass vlan
[sw4-port-group]port trunk allow-pass vlan 2
[sw4-Ethernet0/0/5]port trunk allow-pass vlan 2
[sw4-Ethernet0/0/2]port trunk allow-pass vlan 2

（3）现在需要进行STP生成树的配置

要求：sw1与sw2之间要进行备份

配置方案：SW1为组1的根（vlan2的备份根） SW2为组2的根（vlan1的备份根）

具体配置：

[sw1]stp enable
[sw1]stp region-configuration
[sw1-mst-region]region-name a
[sw1-mst-region]instance 1 vlan 1
[sw1-mst-region]instance 2 vlan 2
[sw1-mst-region]active region-configuration
[sw1]stp instance 1 root primary
[sw1]stp instance 2 root secondary

[sw2]stp enable
[sw2]stp region-configuration
[sw2-mst-region] region-name a
[sw2-mst-region] instance 1 vlan 1
[sw2-mst-region] instance 2 vlan 2
[sw2-mst-region] active region-configuration
[sw2]stp instance 1 root secondary
[sw2]stp instance 2 root primary

[sw3]stp enable
[sw3]stp region-configuration
[sw3-mst-region] region-name a
[sw3-mst-region] instance 1 vlan 1
[sw3-mst-region] instance 2 vlan 2
[sw3-mst-region] active region-configuration
[sw3]port-group group-member e0/0/1 e 0/0/3
[sw3-port-group]stp edged-port enable
[sw3-Ethernet0/0/1]stp edged-port enable 边缘接口
[sw3-Ethernet0/0/3]stp edged-port enable 边缘接口

[sw4]stp enable
[sw4]stp region-configuration
[sw4-mst-region] region-name a
[sw4-mst-region] instance 1 vlan 1
[sw4-mst-region] instance 2 vlan 2
[sw4-mst-region] active region-configuration
[sw4]port-group group-member e 0/0/1 e 0/0/3
[sw4-port-group]stp edged-port enable
[sw4-Ethernet0/0/1]stp edged-port enable 边缘接口
[sw4-Ethernet0/0/3]stp edged-port enable 边缘接口

查看后发现STP已经做到了vlan1和vlan2都有备份的要求

（4）进行SVI的创建和配置和进行VRRP的配置，即进行网关备份配置

首先在SW1和SW2上创建SVI1和SVI2并且配置ip：

[sw1]int vlan1
[sw1-Vlanif1]ip add 172.16.1.10 25
[sw1-Vlanif1]int vlan2
[sw1-Vlanif2]ip add 172.16.1.210 25

[sw2]int vlan 1
[sw2-Vlanif1]ip add 172.16.1.20 25
[sw2-Vlanif1]int vlan 2
[sw2-Vlanif2]ip add 172.16.1.220 25

下来进行VRRP的配置：

[sw1]int vlan1
[sw1-Vlanif1]vrrp vrid 1 virtual-ip 172.16.1.30 配置
[sw1-Vlanif1]vrrp vrid 1 priority 105 修改优先级
[sw1-Vlanif1]vrrp vrid 1 track interface gi 0/0/1 上行链路追踪

[sw1]int vlan 2
[sw1-Vlanif2]vrrp vrid 1 virtual-ip 172.16.1.230

[sw2]int vlan1
[sw2-Vlanif1]vrrp vrid 1 virtual-ip 172.16.1.30
[sw2-Vlanif2]vrrp vrid 1 virtual-ip 172.16.1.230
[sw2-Vlanif2]vrrp vrid 1 priority 105
[sw2-Vlanif2]vrrp vrid 1 track interface gi 0/0/1

查看：

（5）最后在SW1和SW2上创建DHCP

SW1：

[sw1]dhcp enable
[sw1]ip pool a
[sw1-ip-pool-a]network 172.16.1.0 mask 25
[sw1-ip-pool-a]gateway-list 172.16.1.30
[sw1-ip-pool-a]dns-list 14.14.14.14
[sw1]ip pool b
Info:It's successful to create an IP address pool.
[sw1-ip-pool-b]network 172.16.1.128 mask 25
[sw1-ip-pool-b]gateway-list 172.16.1.230
[sw1-ip-pool-b]dns-list 14.14.14.14

[sw1]int Vlanif 1
[sw1-Vlanif1]dhcp select global
[sw1-Vlanif2]dhcp select global

SW2：

[sw2]dhcp enable
[sw2]ip pool a
[sw2-ip-pool-a]network 172.16.1.0 mask 25
[sw2-ip-pool-a]gateway-list 172.16.1.30
[sw2-ip-pool-a]dns-list 14.14.14.14
[sw2-ip-pool-b]network 172.16.1.128 mask 25
[sw2-ip-pool-b]gateway-list 172.16.1.230
[sw2-ip-pool-b]dns-list 14.14.14.14
[sw2-ip-pool-b]q
[sw2]int Vlanif 1
[sw2-Vlanif1]dhcp select global
[sw2]int vlan2
[sw2-Vlanif2]dhcp select global

现在在下面的pc上开启DHCP自动获取ip

pc1：

pc2：

三、现在交换机部分已经配置完成了，下来配置路由器部分

首先配置公网：

[ISP]int gi 0/0/0
[ISP-GigabitEthernet0/0/0]ip add 172.16.3.1 24
[ISP-GigabitEthernet0/0/0]int lo0
[ISP-LoopBack0]ip add 1.1.1.1 24

r1和下面的两个三层交换机

[r1]int gi 0/0/0
[r1-GigabitEthernet0/0/0]ip add 172.16.3.2 24
[r1-GigabitEthernet0/0/0]int gi 0/0/1
[r1-GigabitEthernet0/0/1]ip add 172.16.0.1 30
[r1-GigabitEthernet0/0/1]int gi 0/0/2
[r1-GigabitEthernet0/0/2]ip add 172.16.0.5 30

下面配置SW1和SW2在与交换机（核心层）连接的线路的ip

这里注意：由于模拟器的缘故无法直接在接口上配置ip修改为创建一个专属的AVI接口在这条线路上

[sw1]vlan 99
[sw1]int gi 0/0/1
[sw1-GigabitEthernet0/0/1]port link-type access
[sw1-GigabitEthernet0/0/1]port default vlan 99
[sw1]int Vlanif 99
[sw1-Vlanif99]ip add 172.16.0.2 30

[sw2]vlan 99
[sw2-GigabitEthernet0/0/1]port link-type access
[sw2-GigabitEthernet0/0/1]port default vlan 99
[sw2]int vlan 99
[sw2-Vlanif99]ip add 172.16.0.6 30

测试：

下面进行路由：

方法：使用OSPF并且分为两个区域area 0 和 area 1

r1：

[r1]ospf 1 router-id 1.1.1.1
[r1-ospf-1]area 0
[r1-ospf-1-area-0.0.0.0]network 172.16.0.1 0.0.0.0
[r1-ospf-1-area-0.0.0.0]network 172.16.0.5 0.0.0.0

SW1：

[sw1]ospf 1 router-id 2.2.2.2
[sw1-ospf-1]area 0
[sw1-ospf-1-area-0.0.0.0]network 172.16.0.2 0.0.0.0
[sw1-ospf-1]area 1
[sw1-ospf-1-area-0.0.0.1]network 172.16.1.10 0.0.0.0
[sw1-ospf-1-area-0.0.0.1]network 172.16.1.210 0.0.0.0

SW2：

[sw2]ospf 1 router-id 3.3.3.3
[sw2-ospf-1]area 0
[sw2-ospf-1-area-0.0.0.0]network 172.16.0.6 0.0.0.0
[sw2-ospf-1]area 1
[sw2-ospf-1-area-0.0.0.1]network 172.16.1.20 0.0.0.0

[sw2-ospf-1-area-0.0.0.1]network 172.16.1.220 0.0.0.0

查看邻居的建立：

对sw1与sw2之间的两个邻居进行汇总让r1只会学习一条到这里的路由

[sw1-ospf-1-area-0.0.0.1]abr-summary 172.16.1.0 255.255.255.0

[sw2-ospf-1-area-0.0.0.1]abr-summary 172.16.1.0 255.255.255.0

为了让内网中的用户可以访问到公网需要在r1上做一条缺省指向公网

[r1]ip route-static 0.0.0.0 0.0.0.0 172.16.3.1

[r1]ospf 1
[r1-ospf-1]default-route-advertise

这里可以对SW1和SW2上进行优化制作沉默接口

[sw1-ospf-1]silent-interface all
[sw1-ospf-1]undo silent-interface Eth-Trunk 0
[sw1-ospf-1]undo silent-interface GigabitEthernet 0/0/1
[sw1-ospf-1]undo silent-interface Vlanif 1

[sw1-ospf-1]undo silent-interface Vlanif 99

[sw2-ospf-1]silent-interface all
[sw2-ospf-1]undo silent-interface Eth-Trunk 0
[sw2-ospf-1]undo silent-interface GigabitEthernet 0/0/1
[sw2-ospf-1]undo silent-interface GigabitEthernet 0/0/1
[sw2-ospf-1]undo silent-interface Vlanif 1

[sw2-ospf-1]undo silent-interface Vlanif 99

四、最后进行ANT配置

[r1]acl 2000
[r1-acl-basic-2000]rule permit source 172.16.0.0 0.0.255.255
[r1]int gi 0/0/0
[r1-GigabitEthernet0/0/0]nat outbound 2000

五、测试

pc1ping公网：

pc2ping公网